|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
INTEGRATED CIRCUITS 74F30244 Octal 30 line driver with enable, non-inverting (open collector) Product specification Supersedes data of 1999 Jan 08 IC15 Data Handbook 2000 Jun 30 Philips Semiconductors Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 FEATURES * Ideal for driving transmission lines or backplanes. 160mA IOL ideal for applications with impedance as low as 30 DESCRIPTION The 74F30244 is a high current open collector octal buffer composed of eight inverters. The 74F30244 has non-inverting paths. The device has eight inverters with two Output Enables (OE0, OE1), each controlling four outputs. The driver is designed to deal with the low-impedance transmission line effects found on printed circuit boards when fast edge rates are used. The 160mA IOL provides ample power to achieve TTL switching voltages on the incident wave. TYPICAL PROPAGATION DELAY 10.5ns TYPICAL SUPPLY CURRENT (TOTAL) 69mA * Guaranteed threshold voltages on the incident wave while driving line as low as 30 * High impedance NPN base inputs for reduced loading (20A in High and Low states) * Ideal for applications which require high output drive and minimal bus loading * Octal interface * Non-inverting * Open-Collector outputs sink 160mA * Multiple side pins are used for VCC and GND to reduce lead inductance (improves speed and noise immunity) TYPE 74F30244 * Available in 24-pin standard slim DIP (300mil) plastic or SOL ORDERING INFORMATION DESCRIPTION 24-pin Plastic Slim DIP (300mil) 24-pin Plastic SOL1 COMMERCIAL RANGE VCC = 5V 10%, Tamb = 0C to +70C N74F30244N N74F30244D PACKAGE DRAWING NUMBER SOT222-1 SOT137-1 NOTE: 1. Because of the high current sinking capability of these parts, the SOL package should only be used under the following conditions: a. 50% duty cycle, AND b. 3/5 of remaining 50% driving 100mA (leaving the remaining 2/5 of the drive 160mA) OR c. use 450 linear feet per minute forced air or other thermal mounting techniques. INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS D0-D7 OE0-OE1 Q0-Q7 Data inputs Output Enable inputs (Active Low) Data outputs (OC) DESCRIPTION 74F(U.L.) HIGH/LOW 1.0/0.033 1.0/0.033 OC/266.7 LOAD VALUE HIGH/LOW 20A/20A 20A/20A OC/160mA NOTE: One (1.0) FAST unit load is defined as: 20A in the High state and 0.6mA in the Low state. OC = Open Collector. 2000 Jun 30 2 853-1157 24025 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 PIN CONFIGURATION Q0 Q1 Q2 Q3 GND GND GND GND Q4 1 2 3 4 5 6 7 8 9 24 D0 23 D1 22 D2 21 D3 20 OE0 19 VCC 18 VCC 17 OE1 16 D4 15 D5 LOGIC DIAGRAM D0 24 1 Q0 D1 23 2 Q1 D2 22 3 Q2 D3 21 4 Q3 OE0 20 Q5 10 Q6 11 Q7 12 D4 14 D6 13 D7 D5 16 9 Q4 15 10 Q5 SF01388 D6 14 11 Q6 LOGIC SYMBOL 24 23 22 21 16 15 14 13 D7 13 12 Q7 OE1 VCC = PIN 18, 19 GND = PIN 5, 6, 7, 8 17 D0 D1 D2 D3 D4 D5 D6 D7 20 17 OE0 OE1 Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 SF01394 VCC = PIN 18, 19 GND = PIN 5, 6, 7, 8 1 2 3 4 9 10 11 12 SF01390 IEC/IEEE SYMBOL 20 17 EN1 EN2 1 2 3 4 9 10 11 12 24 23 22 21 16 15 14 13 1 SF01392 2000 Jun 30 3 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 FUNCTION TABLE INPUTS OEn L L H H L X OFF = = = = High voltage level Low voltage level Don't care Pulled up through resistor (Open Collector) Dn L H X OUTPUTS Qn L H OFF ABSOLUTE MAXIMUM RATINGS (Operation beyond the limits set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL VCC VIN IIN VOUT IOUT Tamb Tstg Supply voltage Input voltage Input current Voltage applied to output in High output state Current applied to output in Low output state Operating free-air temperature range Storage temperature range PARAMETER RATING -0.5 to +7.0 -0.5 to +7.0 -30 to +5 -0.5 to VCC 320 0 to +70 -65 to +150 UNIT V V mA V mA C C RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL VCC VIH VIL IIK VOH IOL Tamb Supply voltage High-level input voltage Low-level input voltage Input clamp current High-level output voltage Low-level output current Operating free-air temperature range 0 PARAMETER MIN 4.5 2.0 0.8 -18 4.5 160 +70 NOM 5.0 MAX 5.5 V V V mA V mA C UNIT 2000 Jun 30 4 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL IOH VO OL VIK II IIH IIL ICC PARAMETER High-level output current TEST CONDITIONS1 VCC = MIN, VIL = MAX, VIH = MIN, VOH = MAX VCC = MIN, VIL = MAX MAX, VIH = MIN IOL = 100mA IOL = 160mA3 10% VCC 5% VCC -0.73 0.42 LIMITS MIN TYP2 MAX 250 0.55 0.80 -1.2 100 20 -20 19 VCC = MAX 70 27 100 UNIT A V V V A A A mA mA Low-level Low level output current Input clamp voltage Input current at maximum input voltage High-level input current Low-level input current Supply current y (total) 74F30244 ICCH ICCL VCC = MIN, II = IIK VCC = 0.0V, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25C. 3. IOL1 is the current necessary to guarantee the High-to-Low transition in a 30 transmission line on the incident wave. AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION Tamb = +25C VCC = +5.0V CL = 50pF, RL = 500 MIN tPLH tPHL tPLH tPHL Propagation delay Dn to Qn Propagation delay OEn to Qn Waveform 1 Waveform 1, 2 4.0 3.0 4.0 3.5 TYP 10.5 5.5 9.5 6.0 MAX 14.5 9.0 14.0 9.0 Tamb = 0C to +70C VCC = +5.0V 10% CL = 50pF, RL = 500 MIN 4.0 3.0 4.0 3.5 MAX 15.0 9.5 14.5 10.5 ns ns UNIT AC WAVEFORMS For all waveforms, VM = 1.5V. Dn, OEn VM tPLH Qn VM VM tPHL VM Qn Dn, OEn VM tPHL VM VM tPLH VM SF01384 SF01385 Waveform 1. Propagation Delay for Data to Output Waveform 2. Propagation Delay for Data to Output 2000 Jun 30 5 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 TYPICAL PROPAGATION DELAYS VERSUS LOAD FOR OPEN COLLECTOR OUTPUTS 9 tPLH 8 7 PROPAGATION DELAY (ns) 6 5 4 tPHL 3 2 1 0 0 100 200 300 LOAD RESISTOR () 400 500 600 NOTE: When using Open-Collector parts, the value of the pull-up resistor greatly affects the value of the tPLH. For example, changing the specified pull-up resistor value from 500 to 100 will improve the tPLH up to 50% with only a slight increase in the tPHL. However, if the value of the pull-up resistor is changed, the user must make certain that the total IOL current through the resistor and the total IILs of the receivers does not exceed the IOL maximum specification. SF01386 TEST CIRCUIT AND WAVEFORMS VCC 7.0V 90% VIN PULSE GENERATOR RT D.U.T. VOUT RL NEGATIVE PULSE VM 10% tTHL (tf ) CL RL tTLH (tr ) 90% POSITIVE PULSE 10% tTHL (tf ) AMP (V) 90% VM tw 10% 0V tw VM 10% tTLH (tr ) 0V 90% AMP (V) Test Circuit for Open Collector Outputs VM DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate 1MHz tw 500ns tTLH 2.5ns tTHL 2.5ns SF00027 2000 Jun 30 6 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 DIP24: plastic dual in-line package; 24 leads (300 mil) SOT222-1 2000 Jun 30 7 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 SO24: plastic small outline package; 24 leads; body width 7.5 mm SOT137-1 2000 Jun 30 8 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 NOTES 2000 Jun 30 9 Philips Semiconductors Product specification Octal 30 line driver with enable, non-inverting (open collector) 74F30244 Data sheet status Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Production [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 2000 All rights reserved. Printed in U.S.A. Date of release: 06-00 Document order number: 9397-750 07281 Philips Semiconductors 2000 Jun 30 10 |
Price & Availability of 74F30244 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |